• Skip to primary navigation
  • Skip to content
  • Skip to primary sidebar
Top Pump Reviews

Top Pump Reviews

Top Rated And Best Selling Pumps And Related Others

  • Ultimate Guides
  • Reviews
  • Blog

How To Replace Sump Pump Check Valve

Updated November 14, 2020 By Richard Shuback

For a sump pump to run efficiently a check valve is important equipment. A sump pump is known to drain water from places like some areas of your house. The work of a check calve is to prevent backflow of water to the sump pump. It is know that a sump pump check valve is found at the sump pump system’s discharge area. Replacing it just takes you a few couple of hours. A check valve is known to be a one way valve.

There are various check valves suitable for your sump pump depending on the features you want and if its main role is well manipulated and worked at. Good check valves are not a problem in loud noises, hammering or also clapping. The quality ones are made in a way that they reduce the disgusting loud noises and there installation is easy and standard. Lately many users want to replace their check valves and the question is, how to replace sump pump check valve?

Failure of the check valve to work leads there will be backflow of the already pumped water into the discharge line and this will lead to your pump working too hard. This failure and the results will lead to great loses in that there is a probability of burning up the engine of your pipe or flooding and this requires replacement of a check valve. And faster troubleshooting of the sump pump check valve is the right choice to make but what kind of sump pump check valve do you want. What I can tell you is to look for the latest models in the market which in advantage they are budget friendly and also they are easy to find. These models are designed in a way that they are quiet and they don’t make a lot of clapping noise while they open and close.

Replacement of the check valve depends on its condition. It also depends whether it is old enough that you as the user you need its replacement. This is according to your own sump pump. So how do you replace the sump pump check? This is the question most of you end up with since you see replacing it being a lot of work.

Steps On How To Replace Sump Pump Check Valve

The following are the steps to successfully and easily replace sump pump check valve:

1.

Safety and preparation

Before you begin the replacement you should ensure that the sump pump system should finish its cycle and all water in the sump pump is drained. Then you can go on to disconnecting the power supply system to the sump pump. For safety measures ensure that while disconnecting the discharge pipe ensure nothing of value is anywhere near since when removing the old check valve some water may spill.

2.

Removal of the old check valve or also the failed check valve

Removal of the check valve depends on the type of the check valve you dealing with. Removing the check valve you need PVC cutters to cut on both ends above and below in order to make loose the hose clamps sides (top and bottom).

3.

Installing the new valve

While cutting the PVC discharge pipe you should ensure the space cut is not larger than the one you replacing with. But if it happens that the space is larger then you can go a step ahead of removing more of the discharge line in order to keep the discharge pipe with the replacement check valve in line. And also you can add PVC coupling that is in line with the length of PVC that will guarantee proper fitting. The reason for doing this is because the replacement check valve should be able to hold onto the PVC discharge pipe together with the hose clamps at the top and bottom.

In the process of installing the check valve, marking the direction of water valve at the check valve is important. Then do the installation of the replacement valve ensuring that the arrow is pointing the drain line and it is away from the sump pump.

4.

Bracing the discharge pipe

to avoid the discharge pipe from pulling apart at the replaced check valve then it should be supported properly.

You have to know: Zoeller vs Wayne Sump Pump

How To Prime A Water Transfer Pump

Updated November 14, 2020 By Richard Shuback

Many are the times which water pump run out of pressure and definitely stop working after they are turned off for an extended period. An example of such a period is over the winter season. Priming a water transfer pump is, therefore, getting the pump to start working again. Water has to be flushed into the pump and after that forced through it so that enough pressure can be recreated again, ensuring the pump gets to work again. You should know that turning on a pump that has not been primed poses a risk to the motor and the pump at large. Since water transfer pipes are of different types, the priming methods to be applied can slightly vary. However, below are some of the necessary steps.

Steps On How To Prime A Water Transfer Pump

1. You should first turn off the water transfer pump before you begin the procedure

It would be best if you never fiddled with a device while it is on. Ensure that any electrical power that is connected to the pump is turned off. You can do this by going at the base of the pump and turning it off or at the breaker panel

2. Find a plumbing fixture that allows you to access the pump system

Most of the water transfer pumps have such fixtures located close to the water tank. However, if you are working on a pool pump, the accessory will be the strainer basket.

3. Thoroughly inspect the system for any damages

You can do this by looking for cracks and other damages on all the piping and fittings. Such damages can occur if the system was off over winter. Ensure that any nuts, bolts, and drain plugs are all in good condition, tightened and fitted properly.

4. Look for a hose\pipe that can be connected to a water source

The hose that you choose should be large enough to be connected to an independent water source. You can use your garden hose (if you have any). Also, ensure that this hose is clean and free from any material that can contaminate the water. After settling on the hose, run a substantial amount of water through it to flush.

You might come across a hose that has some relief valves. Open all of the valves. This will ensure that no pressure builds up in it. You should, however, monitor the water pressure gauge while doing this.

5. Now insert the hose into the plumbing fixture

This fixture is the one that was mentioned in step (ii). After inserting the hose, turn on the water source and let water flow through it. At this point you should hear some air starting to flow within the system. You should also hear water filling your tank. For those with a water pressure gauge, just look at it, you’ll notice the water level rising.

6. Turn off the water connected to the hose

Immediately after you notice water coming out of the opposite end, turn off the water pump flow that you had connected to the hose. If the water stops flowing at that end, it means that the system has been pressurized and the priming was successful. The process might also fail, and you will, therefore, be required to repeat the whole process over again. This is the reason why you are not supposed to disconnect the hose before confirming that the process was successful.

After you confirm that the process was successful, you can now turn on the power and turn on the pump system again. After turning it on, allow it to run for a moment (a minute or two). You might have opened the valves on the pump. In such a scenario, wait until you see water beginning to seep from the valves, and then immediately close them. Bear in mind that the pump might refuse to run. This can be caused by the pressure in the water tank being above or at the same level as the cutout pressure of the pump

After the pump finishes its cycle and turns on automatically, the mission is complete. The pump refusing to turn on is normal and you will just be required to repeat the six simple steps until you get it to work.

Water pumps are powerful and at the same time, valuable equipment. That is why they should receive adequate care and maintenance.

How To Drain A Pool Without A Pump

Updated November 14, 2020 By Richard Shuback

Once the weather turns cooler it is time to empty the pool. Many people think they need a pump to drain the pool and remove all of the water. That is not the case. There are some ways to drain the pool without using a pump.

Easy Steps On How To Drain A Pool Without A Pump

1.

Siphoning

This is the least expensive method for draining the pool. It can be used on built-in pools and above ground pool. That that is needed is a hosepipe and a place for the water to go. A person needs to be aware of any water that will flood into neighboring yards and the mud it will create. This is one of the easiest methods for removing the water from the pool.

Once a person has the hose they will insert it into the pool. It should be just about touching the bottom. The other end should be placed in the area where the water is going to drain. To begin to get the water out of the pill suck on the end of the hole that is not in the water. Do this until the water is coming out. They need to be careful to stop sucking on the hose right before the water exits or they may end up with a mouthful of pool water. Once the water starts flowing out of the hose it will not stop until the water is the pool is just about empty. Air will then enter the hose signaling that the water is empty. There will only be a small puddle of water left in the pool and it will be just about empty.

2.

Use a Trash Pump

This is not exactly a pump but will work similarly as a pool pump. This pump is used to keep the pool water clean and remove debris from it. These pumps can be rented from the local pool supply store and they are rented out by the day at an affordable rate. The trash pump has a suction and a discharge hose. These items are connected and then connected to the pool. Once everything is connected the water will be drained. The entire pool can be done in 1 to 2 hours which is pretty quick. The process is automated and all a person will need to do is check on the trash pump from time to time. Renting a trash pump is much less expensive than purchasing this pump or even purchasing a pool pump. Once the water is out they can bring it back to the store on the same day that they rented it.

3.

Bucket Method

The buckets and basins have been used for years to remove water from the pool. They will work but are recommended for people with a smaller pool. A place for the water to be drained is also needed. A person will need to get inside the pool and scoop out the water. It is recommended to get some help when doing this as it can be tiring.

4.

Vacuum Pump

The pump used to clean the pool can be used to help remove water from the pool. The vacuum pole will need to be connected to the vacuum head. The discharge hose and the pump will then be turned on so that the water will be removed from the pool. The water will be pumped from the pool using the vacuum. If a person already has this tool they can use it to remove the water from the pool.

Things To Remember About Draining The Pool

Draining the water out of the pool is going to take time. a person should be aware of the area around the pool. If too much water saturates the ground it can push the pool up. Without water in the pool, the pool does not have a lot of weight and can be pushed. The pool should not be drained after a rainstorm as the ground is already saturated with water.

These are some ways to empty a pool without having to go out and purchase a pool pump. These methods are effective at removing the water from the pool so that a person can prepare it for the winter. They are also cost-efficient and will help a person save money when it comes to pool care and maintenance.

How to Clean a Pool Pump Impeller

Updated November 14, 2020 By Richard Shuback

The days when people are having a hot summer are more bearable, especially when bearing a pool in which you need to dip in the backyard. However, ensure you do not forget the part on maintenance after enjoying enough in your pool. Besides, it will not matter if one is an aboveground pool or also is in an in-ground one. There will be a necessity of making sure it is staying clean you the sake of the success of the next session on entertainment.

This is the main reason as to why most of the individuals are preferring purchasing swimming pool pumps. Besides, there is a need for understanding that the cleaning pool accessory is requiring maintenance from one time to the other. In particular, the impeller is requiring even much more support.

The Procedure On How To Clean A Pool Pump Impeller

As a result, there is a need to follow this guide on the procedure on how to clean a pool pump impeller, and it will assist you in understanding its necessity for the hygiene of the pool.

Identification of the Issue by Use if Impeller

Before you consider moving around with your cleaning guide, there is a necessity if understanding the different aspects of the

identification of the pump problems

When the filter pressure is low, or the motor pump sound is restricted, there is the necessity of acting immediately. There are many times in which you will find the pump impeller highly clogged with various pollutants, and thus there will be a necessity of cleaning it up.
The clogging of the pump impeller, in most cases, happens when the pool has been located in a place with trees, including the palm. The various delicate leaves of that kind of a tree will be tending to be jamming the impeller from time to time.

Impeller Location

The impeller is usually located beside the motor basket pump, which is referred to as the impeller housing. As a result, it is the basket's responsibility to be keeping debris and pollutants away from the house of the impeller, which might end up clogging the impeller.

Besides, the motor basket pump is not offering 100% debris protection. As a result, there will be various particles that are small-sized that will also end up jamming the impeller through the process of entering the pump basket.

As a result, there is a necessity of understanding that a given element can clog an impeller, especially while bearing the appropriate size. For instance, sand may end up entering in the basket and will restrict the impeller movement.

Other different elements will end up passing through such as pine needles, tree flower stamens, small seeds, grass clippings, small pebbles and pool plaster particles.

More also, there is also the necessity of understanding that various impellers are in place and are referred to as 'closed vane' impellers. They are named this way as a result of the presence of a covering that is in the front. Besides, it assists in the creation of a vacuum to draw water outside and inside of the motor pump.

Additionally, the various impellers are bearing a higher suction power, which is best for many of the fluids. Besides, there are various open-vane valves widely referred to as vortex impeller since they are not bearing a closed system.

They may not be having a higher sanction power as they will not do not have the clogging advantage. They are found mostly in larger pumps for brass-based and trash pool pumps.
For the sake of protection of the impeller, the unit has been attached to the impeller plate or even the diffuser to create a sanction pressure. More also, you might also need to wear a ring which will be positioned in an impeller on the motor pump.

Steps On How To Clean A Pool Pump Impeller

1

Inspecting before cleaning

There is a necessity of checking the filter and pump basket for clogged particles.

2

Inspecting the hoses for cracks

The step involves checking on whether the hoses have cracks in them or not.

3

Moving to the Impeller

You will require a shirt hanger and a set of pliers for the upcoming steps.

4

Turning off the power supply

Go to the place you have the house circuit breaker and afterwards switch off the active power supply for the motor pump.

5

Remove the Lid and Pump Basket

Unscrew the pump basket lid and also removed the basket, which is attached to the impeller.

6

Making a hook

By the use of pliers, bend the hanger wire into a small-sized hook.

7

Looking for Debris

Insert the hook inside the opening of the impeller to scrub to remove the debris present inside.

8

Priming the pump

It involves putting the pump basket back to its position.

9

Turning on the power

Consists of switching on the power supply by the house circuit board and starting the pump again.

Conclusion

These tips must have been of help to you. Always remember that prevention is essential to have the surety of machine longevity.

You can read the Water Pressure Booster Pump Reviews article also.

How To Wire A Bilge Pump Float Switch

Updated November 14, 2020 By Richard Shuback

The bilge pump is designed so it can remove the bilge water, and any boat needs to have it so it can freely sail. This pump requires installation and wiring, which are known to be so costly, but it is the best since it reduces for you all the enlisting third party expenses. Here are the ways you can use to wire float switch bilge pump safely.

Steps For Wiring Bilge Pump With Float Switch

#1. Ensure the bilge pump is safely mounted on the bilge. Ensure they are restrained, so they don't fall and get damaged as they intake air

#2. Use brackets to fasten bilge pump or with epoxy so you can attach bolts at the bottom of the bilge that will be the mounting studs.

#3. Mount on your float switch

#4. Use the smooth interior hose to connect your pump with discharge.

#5. Ensure the tube is little, so the hose line coming from landfills can straightly pump. Ensure you have a straight and short hose when wiring the bilge pump to avoid reduced bilge outage.

#6. Ensure discharge is well mounted on the waterline. This submerged discharge can siphon to the bilge severally so the pump can heat several times to ensure the battery is exhausted.

#7. Ensure bilge pump is lead out and up from the bilge in intervals

#8. Ensure wiring is secured it doesn't contact with water

#9. Ensure bilge pump size wiring is enough. Check your pump's literature severally to know the suggested allowable distance and wire size. You can be in contact with manufacturers to know the recommended wire size if you don't get to understand it. Ensure you use a low voltage drop below 3% and voltage drop calculator usage. With appropriate were size, you will know if you have enough wire as per the requirements of the pump.

#10. Use the butt connectors where you apply enough heat for tubing shrinking.

#11. Ensure the pipe is centered on the butt connectors where adequate heat is applied for shrinking your tubing

#12. Ensure the bilge pump is connected with the battery. Dont follow the description panel in your wiring process since power should always come to the bilge pump even with control off in the boat.

#13. Has fuse installed next to the battery in the positive wire

#14. When you don't get a fuse in switch panel, attach it with a butt connector.

#15. Ensure cables are loop supplied in the terminal wing nuts of the batterie but dont strip wires.

#16. Crimp-on ring terminals should be installed with the copper washer in the wingnuts and ring terminals

#17. Float switch should be wired with the 3-way switch so you can freely select the automatic mode on or off.

How To Install A Float Switch

1.

Know The Low Point - It is essential to start to sing your low point to prevent your level from going beyond NPSH that is required in your pump installation. This NPSH is known to be the suction pressure, which is highly needed by your pumps, so there should not be cavitation, among other issues.

2.

Mount On Float Switch - It is a necessity that you need to mount on your device using some fixing ways of the cable on the well or the tank. Ensure you get some mounting bracket in the float switch, which requires a comfortable wedge for fixing the wire in place. The bracket is easily attached to the roll or even wall with a screw or bolt.

3.

Adjusting The Weight - Weight will always determine the space in these two higher points. This will enable you to know if it needs to be modified or not.

4.

Do The Wiring - After knowing your weight position and the levels of switches, you should then have an installation of a wiring float switch to have an enclosure waterproof. Cable entrance must always be sealed using the cable gland.

Conclusion

After you have finished doing the installation of the float switch, you will be sure that your boat pump is ready for the work. There will only be a few adjustments you can do when the ship is making its first trip; then, it will be perfectly well and ready for the job.

How To Test An Oil Pump

Updated November 14, 2020 By Richard Shuback

Oil is crucial to the proper functioning of every automobile. It lubricates the moving parts of the engine to avoid them from grinding each other and the oil absorbs excess heat. You should change the oil regularly and use the proper oil weight. Also, make sure that the pump distributes it is in good condition. If you suspect that there is an issue with the pump, you can quickly test and repair it before it causes permanent damage. An oil pump promotes oil circulation and keeps your engine in top condition. In case of a pump failure, most engine parts can wear or burn through friction.

Common symptoms of oil pump errors

The oil light indicator on the dashboard informs you about engine problems. Do not ignore it when it is on, as it may indicate a possible low oil pressure.

Continue to check the dipstick and add oil if the level is low. If the indicator light stays on, this may indicate an error in the oil pump. Other signs include:

i. Overheating of the engine

As already mentioned, vehicles must be well lubricated always. This will avoid friction between the moving parts and thus to regulate their temperature.

If an oil pump fails, the oil distribution will be affected and most moving parts will not be lubricated well. Without proper lubrication, these parts rub against each other and heat up.

ii. Noise

Car engines have hydraulic lifters that work quietly when the engine is working correctly. If they are not lubricated well, they cause excessive noise and may cause uneven wear.

The valve train, which consists of pushrods, seals and valve guides, also makes noise when the engine is not well lubricated. Replacing these components can be very expensive in the long run and the only durable solution is to make sure that the oil reaches all engine parts.

In particular, due to a defect or wear of the internal components, the oil pump may also generate a whirring if it is not appropriately lubricated.

What should you do when testing an oil pump?

It is essential to know what steps to take if you suspect your oil pump is malfunctioning. In essence, you can avoid damage at an early stage before it becomes a severe problem. We can know how to test an oil pump by the following steps: 

i. Stop the vehicle

If you find that the oil pressure gauge is too low, stop the car and check the level of oil on the dipstick. Switch off the vehicle and add oil after a few minutes if the oil level is below the recommended limit. After restarting the engine, check the oil pump for signs of failure.

ii. Check engine oil pressure sender unit

Check the engine oil pressure sending the unit on the engine if the problem persists. If the gauge remains on, there may be an issue with the mechanical transmitter unit. This may be a loose plug in the hole into which oil is entering or faulty wiring.

The worn-out sports that are on the rheostat are the most likely cause of problems with the electrical transmission unit.

iii. Mount the oil pressure gauge on the engine oil connection.

Make sure the oil pressure gauge is attached correctly to the engine oil port. Check the pressure gauge when the engine is running. At this point, the pump may experience some problems if the light does not switch off.

Continue checking the pressure gauge. If the pressure is normal, then the problem may be with the sending unit and not with the oil pump.

Check the filter in the pickup tube and replace it if necessary. At this time, the oil pump may need to be replaced by a mechanic if the problem persists.

How to keep your car engine in top condition?

The best way to avoid significant problems with the engine of your car is to check regularly. You must do the following:

  • Check the oil engine every time you refuel
  • Don’t overfill the crankcase with the oil
  • Change oil regularly
  • Clean the oil pan when changing the oil
  • Use synthetic oil, which is suitable for your engine

Conclusion

Testing an oil pump is one of the necessary procedures that every car owner needs to perform. Even if the process seems simple, you should pay attention to a correct diagnosis.

related resources


  • How To Make A Water Pump At Home
  • How Does A Bilge Pump Work
  • How To Install Sewage Ejector Pump In Basement
  • « Previous Page
  • Page 1
  • Page 2
  • Page 3
  • Page 4
  • Next Page »

Primary Sidebar

As an Amazon Associate I earn from qualifying purchases.


Copyright © 2022 • Top Pump Reviews • All Rights Reserved!

  • Home
  • Affiliate Disclosure
  • Contact
  • About